Mouse FSH ELISA Kit

2. After sample collection, if 1 Testing within weeks can be stored at 4°C , if it cannot be detected in time, please pack it according to the one-time usage amount and freeze it in -20°C （ 1 Within months), or -80°C （ 3-6 Test within a month) to avoid repeated freezing and thawing.
Keep the sample at room temperature prior to the experiment.

If the concentration of the detected substance in your sample is higher than the highest value of the standard, please make an appropriate dilution according to the actual situation (it is recommended to do a pre-experiment first to determine the dilution factor).

Two,
Preparation for testing

1. Please advance 30 Minutes remove the kit from the refrigerator and equilibrate to room temperature.

2. Use double distilled water 25× The concentrated wash liquid is diluted to 1× Working fluid, put back unused 4°C.

3. Standard: Add standard & Sample Universal Diluent 1.0 mL Into the lyophilized standard, screw the tube cap tightly and let stand 10 Minutes, and after it is fully dissolved, gently mix (concentration of 100 mIU/mL).
Thereafter, double dilution is carried out to 100 mIU/mL，50 mIU/mL，25 mIU/mL，12.5 mIU/mL，6.25 mIU/mL，3.13 mIU/mL，1.57 mIU/mL Standard dilution (0 mIU/mL) is a blank hole.
Configure the standard according to the amount you need for later use.
The configured standards are recommended in 15 Add the sample within minutes, and it is not recommended to leave it for too long.

4. Biotinylated antibody working solution: calculate the dosage required for the current experiment before the experiment (according to 100 μL/ Hole meter, should be configured more in actual configuration 100-200 μL), before use 15 Min, concentrated biotinylated antibody was diluted with biotinylated antibody diluent (1:100) into working concentration, use on the same day.
Dilution principle 1 μL Concentrated biotinylated antibody is added to 99 μL In the biotinylated antibody dilution, mix well with a pipette.

5. Enzyme conjugate working solution: calculate the dosage required for the current experiment before the experiment (according to 100 μL/ Hole meter, should be configured more in actual configuration 100-200 μL).
Before use 15 Minutes, dilute and concentrate with enzyme conjugate diluent HRP Enzyme conjugate (1:100) into working concentration, use on the same day.
Dilution principle 1 μL The concentrated enzyme conjugate is added to 99 μL The enzyme conjugate dilution was mixed well with a pipette.

6.TMB Substrate —— Pipette the desired dose of solution and do not pour the residual solution back into the reagent vial again.

attention：

1. Please make sure that all components are dissolved and mixed before use of the kit.
If the reconstituted standard is not used, please discard it.

2. Concentrated biotinylated antibody, the volume of concentrated enzyme conjugate is small, may be dispersed in various parts of the tube during transportation, please 1000×g Centrifugation 1 Minutes to allow the liquid of the tube wall or cap to deposit to the bottom of the tube.
Pipette carefully before use 4-5 The solution was mixed once.
Standard, biotinylated antibody working solution and enzyme conjugate working solution should be prepared according to the required dosage, and the corresponding diluent should be used to prepare without confusion.

3. The concentrated washing liquid taken out of the refrigerator may have crystals, which is a normal phenomenon.
The crystals can be completely dissolved in a water bath or incubator before preparing the washing liquid (the heating temperature should not exceed 40°C).
The wash liquid should be at room temperature when used.

4. Adding samples should be quick, and it is best to control each sample adding within 10 Within minutes, in order to ensure the accuracy of the experiment, it is recommended to use a double hole.
When pipetting reagents, a consistent sequence of addition is maintained from well to well, This will ensure the same hatch time for all holes.

5. During the washing process, the washing liquid remaining in the reaction hole should be patted dry on absorbent paper, and do not put the filter paper directly into the reaction hole to absorb water.
Before reading, pay attention to removing the residual liquid and fingerprints at the bottom, so as not to affect the reading of the microplate reader.

6. Color developer TMB Direct exposure to bright light should be avoided during storage and use.
After adding the substrate, pay attention to the color change in the reaction well.
If the gradient is obvious, please terminate the reaction in advance to avoid too dark color affecting the reading of the microplate reader.

7. The test tubes and reagents used in the experiment are disposable, and it is strictly forbidden to reuse them, otherwise it will affect the experimental results.

8. During the experiment, please wear a laboratory coat and latex gloves for protection, especially when testing blood or other body fluid samples, please follow the national biological laboratory safety protection regulations.

9. The kit components of different lot numbers cannot be mixed (except wash solution and reaction stop solution).

10. The enzyme labeling strips in the kit are detachable plates, please use them in batches according to the experimental requirements.

Three,
Operation steps

1. Before the start of the experiment, each reagent should be balanced to room temperature, and all reagents should be configured in advance.
When reagents or samples are diluted, they should be mixed well, and blistering should be avoided as much as possible when mixing well.
If the sample concentration is too high, dilute with a sample diluent to bring the sample within the range of the kit.

2. Add standard or sample to be tested 100 μL (If the sample needs to be diluted, please refer to the sample dilution principle for the dilution method).
Be careful not to have bubbles.
When adding the sample, add the sample to the bottom of the well of the enzyme label plate, try not to touch the well wall, gently shake and mix well, and add the enzyme label plate.
Cover or coating, 37°C incubation 80 Minutes.
To ensure the validity of the experimental results, please use a new standard solution for each experiment.

3. Discard the liquid in the hole, spin dry, wash the plate 3 Times.
For each well 200 μL Washing with washing solution, soaking 1-2 Minutes, shake off the liquid in the labeled plate (or wash the plate with a plate washer).
After the last wash was complete, the plate was pat dry on absorbent paper.

4. Add biotin antibody working solution per well 100μL (can be advanced 15 Preparation in minutes), the enzyme labeled plate is coated, 37°C incubation 50 Minutes.

5. Discard the liquid in the well and wash the plate 3 Times.
For each well 200μL Washing with washing solution, soaking 1-2 Minutes, shake off the liquid in the labeled plate (or wash the plate with a plate washer).
After the last wash was complete, the plate was pat dry on absorbent paper.

6. Add enzyme conjugate working solution per well 100 μL (can be advanced 15 Minute preparation), 37°C incubation 50 Minutes.

7. Discard the liquid in the well and wash the plate 5 Times.
For each well 200 μL Washing with washing solution, soaking 1-2 Minutes, shake off the liquid in the labeled plate (or wash the plate with a plate washer).
After the last wash was complete, the plate was pat dry on absorbent paper.

8. Add per well TMB Chromogenic substrate solution 90 μL，37°C Incubate in the dark 20 Minutes (shortened or extended as appropriate according to the actual color development, but not exceeding 30 Minutes).

9. Add stop solution to each well 50 μL, terminate the reaction (blue immediately turns yellow at this time).
The sequence of addition of the terminating solution should be the same as that of the developer as possible.
In order to ensure the accuracy of the experimental results, the termination solution should be added as soon as possible after the substrate reaction time expires.

10.
Immediately use a microplate reader in 450 nm The optical density values of each well were measured at the wavelength (OD Value).
The instrument should be preheated before use, and the testing program should be set up.

Results Calculation

1. Of each standard and sample OD Value should be subtracted from the blank hole OD Value.
If a double hole is set, the average value should be taken for calculation.

2. For ease of calculation, although the concentration is an independent variable and OD The value is the dependent variable, and we still use the standard when drawing OD Values as abscissa (X Axis), the concentration of the standard is the ordinate (Y Axis).
At the same time, for the intuition of the test results, the figure provides raw data instead of logarithmic values.
Due to the different experimental operating conditions (such as operator, pipetting technology, plate washing technology and temperature conditions, etc.), the standard curve OD Values will vary.
The standard curve provided is for reference only, and the experimenter needs to establish the standard curve according to his own experiment.
Spent sample OD The value can be calculated on the standard curve to calculate the sample concentration and multiply it by the dilution factor, which is the actual concentration of the sample.
It is recommended to use professional curve drawing software such as curve expert.

Note : This picture is for reference only

• Precision

Intraplate precision (Precision within the assay ):CV%<8%

Three samples with known concentrations were respectively in 1 Test on enzyme label plates 20 Times to evaluate the precision in the assay plate.

Inter-plate precision (Measure inter-plate precision ):CV%<10%

Three samples with known concentrations were respectively in 3 Tested on different enzyme plates 40 Times to assess the accuracy between the assay plates.

• Recovery

Known concentrations of mice were added to different samples FSH, do the recovery experiment, get the recovery range and average recovery rate

• linear

Mice will be added FSH The samples were diluted separately 2 Times, 4 Times, 8 Times, 16 Double the recovery experiment to obtain the recovery rate range

1. If the entire kit is stored at-20 °C, please place the kit at 4 °C the night before the experiment.

2. Salt precipitation will occur when the concentrated washing liquid is stored at low temperature. When diluted, it can be heated in a water bath to help dissolve.

3. The newly opened wells of the enzyme labeled plate may contain a little water-like substance, which is a normal phenomenon and will not have any impact on the experimental results.

4. This kit is intended for laboratory research and development use only, not for human or animal use.

5. Reagents should be treated as hazardous substances and should be handled carefully and properly disposed of.

6. Gloves, lab coats and protective glasses should always be worn to avoid skin and eye contact with terminating solution and TMB. In case of accidental contact, please wash thoroughly with water.